C4UE-P
(no caster board or casters)
Price: $150 + shipping
Actual case weight: 47 lbs.
UPS dimensional shipping weight: 90 lbs.

C6UE-P
(no caster board or casters)
Price: $160 + shipping + UPS oversized charge
Actual case weight:  54 lbs.
UPS dimensional shipping weight: 109 lbs.

C8U-P
Price: $215 + shipping + UPS oversized charge
Actual case weight:  62 lbs.
UPS dimensional shipping weight: 121 lbs.

C12U-P
Price: $235 + shipping + UPS oversized charge
Actual case weight:  86 lbs.
UPS dimensional shipping weight: 149 lbs.

C14U-P
Price: $245 + shipping + UPS oversized charge
Actual case weight:  89 lbs.
UPS dimensional shipping weight: 150 lbs.
 

C16U-P
Price: $255 + shipping + UPS oversized charge
Actual case weight:  95 lbs.
UPS dimensional shipping weight:  150 lbs.

• Heavy duty construction
• 10U, ratcheting  mixer rails
• Tough 3/8" plywood and ABS laminate panels
• 4" swivel casters including two locking style
• Recessed butterfly latches and padded flip handles
• Double walled aluminum edges
• Large steel ball corners
• 18.25" equipment rack depth
• #10 x 32 rack rails both front and back
• Designed for standard 19" rack mount equipment

• Road rack for amplifiers or effects where a rack mount mixer can be mounted in the top of the case.

C16U-P model shown above with covers removed and mixer installed.

These are the EWI Tourcase tm Model CU Series rack cases which have ratcheting mixer rails mounted at the top of the case and an 18.25" rack depth measured from the front rack rails to the rear rack rails.  Currently 6 models are available: C4UE-P (4 space), C6UE-P (6 space), C8U-P (8 space), C12U-P (12 space), C14U-P (14 space), and C16U-P (16 space).

The slant mixer mounting portion of the CU series cases is designed to accommodate mixers with a rack mount requirement of  up to 10U (17.5").  A longer front to back mixer of up to 21" (12U) is possible to mount in this case by extending a portion of the mixer into the front and back lids; however, the mixer rack rails are 17.5" long.  The slant mixer rails are supported at the back with a ratcheting tilt mechanism which allows the mixer to be positioned at 10 different angles ranging from flat or horizontal to a maximum slanted position of 20 degrees. 

The equipment rack rails of the CU cases are actually two spaces longer than the model number implies.  Depending on your mixer height when laid flat or horizontal in the slant top portion of the rack you may or may not be able to use this extra rack space for racking other equipment.  If your mixer extends down into this space when laid flat you will still have the full use of the rated rack space.  Please note:  The supplied panel blanks or a piece of rack equipment must be installed in the front and back rails at all times to provide rigidity to the case.

The CU series side panels are constructed with 3/8 inch hardwood plywood and covered with a black ABS laminate finish.  The extrusion is all double walled aluminum and the case is assembled with quality stainless steel rivets.  The rivets on the 4 recessed padded flip handles are backed with washers to ensure strength and durability.  The cases roll on 4 heavy duty 4" swivel casters, two of which are braking style. The casters are shipped un-mounted with all mounting hardware included.  Please note that the C4UE-P & C6UE-P do not come with casters or a caster board. 

The CU series cases are equipped with 3 lids:  front, back, and top.  The lids are secured to the case using 4 medium sized recessed butterfly latches per lid and the top lid is secured between the front and back lids.  Each lid has four heavy duty ball corners and the inside of the CU series lids are fully padded with medium density foam rubber.  When the mixer rails are horizontal, there is approximately 2 3/4" of clearance between the top of the mixer rails and the inside of the top lid.

These are well made heavy duty cases manufactured to exacting tolerances and suitable for a variety of racking applications.

Yamaha LS9 mounted in a C4UE-P shown above and below